Investigation of Vertical Acceleration of Vehicles in Vertical Curves Using Multi-Body Dynamic Model

Document Type : Research Paper

Authors

Department of Technical and Engineering, Imam Khomeini International University

Abstract

Ride comfort and sight distance are two main parameters of designing roads’ vertical curves. Vertical acceleration is one of the most important criteria for measuring ride comfort in vertical curves. Vertical acceleration equations in geometric design of roads in the literature, such as Green Book of AASHTO, are based on point mass model where vehicle is assumed to be a point object with a specific mass. Considering that vehicle is a multi-body system, dynamic responses of each part of this system can be different from a point object. In this study, CarSim and TruckSim dynamic simulation softwares utilizing Multi-Body (M-B) model are used to investigate more accurately the vertical acceleration, and to compare it with the vertical acceleration of the point mass model. Dynamic responses of three types of vehicles have been investigated under different speeds and grades. Results indicated a significant difference between the results of the two models, depending on the vehicle speed and the road grade, and the point mass model suggested less acceleration such that difference of the vertical acceleration between the point mass model and the M-B model, depending on the vehicle speed and the road grade, ranged 12.6-25.9% for Sedan, 23.8-29.1% for SUV and 29-47.6% for the truck. According to the results of this study, to design vertical curves, the use of M-B dynamic model, according to more accurate simulation of the vehicle, delivers more realistic design.

Keywords

References

AASHTO. 2018. “A policy on geometric design of highways and streets,(green book 2018)”. American Association of State Highway and Transportation Officials, 6th Edition, Washington, D. C.
ADAMS. 2017. “MSC software”. http://www.mscsoftware.com  
CarSim. 2017. “Mechanical simulation corporation”. http://www.carsim.com
Fan, X. and Hu, C. 2012. “The analysis of electric vehicle ride comfort test simulation based on the Adams/car”. Adv. Mater. Res. 569: 552-555.
Harwood, D. W. 2003. “Review of truck characteristics as factors in roadway design”. Transportation Research Board, NCHRP Report 505.
HVOSM. 2017. “McHenry software”. http://www.mchenrysoftware.com
Kontaratos, M., Psarianos, B. and Yotis, A. 1994. “Minimum horizontal curve radius as function of grade incurred by vehicle motion in driving mode”. Transport. Res. Record, 1445: 86-93.
Kordani, A. A. and Molan, A. M. 2015. “The effect of combined horizontal curve and longitudinal grade on side friction factors”. KSCE J. Civ. Eng., 19(1): 303-310.
Kordani, A. A., Sabbaghian, M. H. and Kallebasti, B. T. 2015. “Analyzing the influence of coinciding horizontal curves and vertical sag curves on side friction factor and lateral acceleration using simulation modeling”. Proceedings of the 15th International Symposium on Highway Geometric Design.
Kordani, A. A., Javadi, S. and Fallah, A. 2018. “The effect of shoulder on safety of highways in horizontal curves: With focus on roll angle”. KSCE J. Civ. Eng., 22(8): 3153-3161.
Ma, R., Chen, X. and Yang, J. 2015. “A simulation analysis of vehicle-pavement coupling vibration”. J. Transp. Inform. Safe., 2, 18 p.
National Cooperative Highway Research Program (NCHRP) Report 737. 2014. “Superelevation criteria for sharp horizontal curves on steep grades”. Transportation Research Board, National Research Council, Washington, D. C.
Pacejka, H. B. 2006. “Tire and vehicle dynamics”. SAE International, Butterworth-Heinemann, Burlington, MA.
Varunjikar, T. 2011. “Design of horizontal curves with downgrades using low-order vehicle dynamics models”. The Pennsylvania State University, Pennsylvania, USA.
Wu, B. G., Li, S. P. and Yan, S. F. 2015. “Vehicle ride comfort simulation based on virtual prototyping technology”. Appl. Mech. Mater., 697: 190-193.
Xiong, J. Q., Huang, J. H. and Qun, L. 2012. “Research and implementation of vibration based on analysis of vehicle ride comfort”. Appl. Mech. Mater., 189: 281-284.
Zhang, E., Liu, Z. H., Ji, Z. H., Shan, J. Y. and Wang, D. S. 2010. “Simulation and experimental research on human riding comfort in human-vehicle system”. J. Eng. Design, 17(2): 107-113.
Zhu, M. T., Shao, C. Z. and Wang, G. L. 2010. “Research on road model rebuilding and vehicle simulation of ride comfort based on Carsim software”. Mach. Design Manuf., 10: 78-80.

Files

History

  • Receive Date: 19 December 2019
  • Revise Date: 11 March 2020
  • Accept Date: 12 March 2020

Share

How to cite

Statistics